Take The Phone Out Of the Water As Soon As Possible
Ports for Hands Free Kit, Tiny Hole For Microphone, Charging, USB Cable Connectivity And the Plastic Covers On Cell Phones Even Through Tight Can Freely Allow Water To Enter the Phone in a Just a Few Seconds Of Time.
Stop Using Your Phone Cut the Power
Grab Your Phone Quickly, and Turn it Off Immediately, As Leaving it On Can Cause it to Short Circuit – If It has Been in Water, Assume it is Waterlogged Whether It is Still Working Or Not. If there is Any Sign or Indication Of Moisture On or Within Your Phone Then the First Thing That You Must Do is to Stop Using Your Cell phone. If Possible Remove the Battery and Cut All Power to the Device. If Your Phone is Designed With a Non-Removable Battery Then Power the Phone Off. Do This as Quickly As You Can. Electricity and Moisture Do not bond Well With One Another and When it Comes to Cell Phones You Want to Try to Avoid Any Unnecessary Electrical Shorts as this Could Lead to Permanently Damaging Your Phone and Its Hardware
Take All Of the Phone Parts off
Remove all of the Parts From the Phone Such as its Back Plate, SIM Card, SD card, its battery (as mentioned Above), etc. Open Up all of These Areas to Allow the Phone to Breath a Bit and To Locate Possible Moisture Around these Parts. If any of These Parts are Wet Then Go Ahead and Dry Them Off With a Clean Dry Cloth.
Methods For Dry Wet Phone
Here Are Some Methods That You Can Use That Can Help Speed Up the Drying Time To Dry Wet Phone
If You have a Vacuum Then You Might Be Able to Suck a Lot of That Moisture Out of the Phone. Use Your Hand as a Suction Cup Around the End of the Vacuums Hose and Suck Out the Battery Compartment and Around Any Ports of the Phone Where Liquid or Moisture May Have Gotten Into.
Before Using a Vacuum You Might Also Want to Ground Yourself First to Eliminate Some of the Static Electricity That you might have Built Up in Your Body. Touching a Metal Table, Metal Service Sitting on the Ground, or Any Plugged in Electrical Product With a Metal Ground Pin Should Help You rid yourself of any Static Electricity and Help You Avoid an Electric Shock
Uncooked Rice or Instant Rice is a Well Known Tool Which Can Be Used to Help Absorb Moisture and Help Speed Up the Drying Time of Your Smartphone. Just Keep All of the Pieces That You Took off of the Phone Aside and Burry Your Cell Phone in Rice Within a Sealed Air Tight Container Such as a Piece of Tupperware or a Ziploc bag. This will Allow the Rice to Absorb Moisture From Your Phone and Not From the Air in the Room. You Might Also Consider Rapping Your Phone in a Thin Napkin or Other Thin Material to Help Prevent Rice from Going into Any Places it Shouldn’t. You Don’t Want a Piece of Rice to Find its Way Into Your SD Card Slot or SIM Card Port or Fall Into the Hole Where You Insert a Headphone Jack
Silica Gel Packs
Silica Gel Packs Work Even Better Than Rice and Are One of the Most Effective Ways to Eliminate Moisture From a Cell phone. If You Have Some of These Packets In Your House or if You Want To buy Some Online They Are Pretty Affordable And These Little Silica Gel Packets are Made for Absorbing Moisture and They Do Good Job at it Too.
Just Like the Rice You Can Place Your Phone in a Sealed Container with a Few of These Packets and Let them Start Drawing that Moisture Out of the Phone
Desk Lamp and Or Windowsill
If you Don’t Have Access to Any Silica Gel Packs and You’re Currently Out of Rice Then You May be Able to Put Your Phone Under the Light of a Desk Lamp or On a windowsill On a Warm Sunny Day. These Two Heat Sources Should Be Gentle Enough to Apply Enough Warmth to the Screen in Order to Speed Up the Drying Process While at the Same Time not Applying Too Much Heat Which Could Actually Damage the Phone
Thanks For Reading The Article Guys..I Hope It Will Help You..If You Like This Article Share This With You Friends
Read More :-